RAID 1 Array Incompatible With DVD ROM Optical Drive?
A RAID 5 can comprise any arbitrary number of drives, but in practice it is best to limit the RAID 5 to three or four physical drives, because the performance of AHCI also allows a hard drive to operate at higher speeds than in IDE mode. ATA is still used in new systems, although it is being superseded by SATA. If you believe this post is offensive or violates the CNET Forums' Usage policies, you can report it below (this will not automatically remove the post). navigate here
If the drives are jumpered as master/slave, substituting an 80-wire cable works fine. Press Y to confirm before exiting. Either drive may be connected to either drive connector. The components inside are more than just elderly--they're positively geriatric by modern PC standards.
How To Connect Ide Hard Drive To Sata Motherboard
We have a chance to guarantee our right to repair electronic equipment—like smartphones, computers, and even farm equipment. Modern CPUs tend to max out at around 7.0 to 7.8. If one device is reading or writing, the other device cannot read or write until the active device yields the channel. UltraDMA (80-wire)¶ An UltraDMA (UDMA) cable uses an 80-wire ribbon cable and 40-pin connectors in all three positions.
During boot, before windows set up starts, you should have a key to press to enter raid set up.Have you done that? A RAID 5 provides somewhat better read performance than a single drive. Only very old hard drives and optical drives are limited to PIO mode anyway, so replacing them is a no-brainer. What Are The Two Goals When Implementing A Raid Solution Flag Permalink This was helpful (0) Collapse - Same problem here...
Turn on the computer. Sata And Ide Hard Drives Together After making all of these changes, I checked the system BIOS and, sure enough, DEP was now an option. If only one drive is installed on that cable, that leaves a long "stub" of cable hanging free with nothing connected to it. Even when I'm loading Windows 7 64bit, I'm loading from the DVD.As I was looking through the BIOS, one of the options said something like (if enabled, you should set some
Tell them repair is good for farmers, good for consumers, and good for businesses. Ide Hard Drive Jumper Settings The only incompatibility I encountered was the RAID array. My final equipment change involved the graphics card: I replaced the AGP 9800XT with a Radeon HD 6450, a very low-end card that required no power connection. Has anyone found models that work reliably with AHCI mode on?
Sata And Ide Hard Drives Together
If you're upgrading a system that has a PIO mode device installed, if possible reconfigure it for DMA. I have a SATA drive as the primary and and IDE slave. How To Connect Ide Hard Drive To Sata Motherboard At this point, Windows XP began generating memory errors. Ide And Sata Drives In Same Computer After boot windows xp/operating system on HD SATA, i re-activate IDE HDs and after backup data, repartitioned like i want. 5.
If there is any meta-data in the master boot record on the new hard drive, it confuses the RAID. check over here Still, even discounting the GPU, the system seemed more responsive when running Windows 8. Tell them repair is good for farmers, good for consumers, and good for businesses. For such a device, jumper it as master if it is the master device on the interface, slave if it is the slave device on the interface, and sole/only if it Motherboard With Ide And Sata Ports
Figure : Example of SATA connections on a hard drive Power cable SATA data cable Figure : SATA connector cables Figure : SATA ports on the motherboard Selecting which SATA port i thought it would be helpful to those wiv the same problemshope this helpsbabs Flag Permalink This was helpful (0) Collapse - SATA & IDE Combination Troubles--but w/ SATA adapters IDE's I uninstalled the license server and a few other applications, mainly to make the system small enough to back up to the secondary 250GB RAID array. his comment is here We have a chance to help the environment and stand up for local repair jobs—the corner mom-and-pop repair shops that keep getting squeezed out by manufacturers.
Although this is a good idea in theory, in practice it seldom works. How To Make Ide Boot Instead Of Sata Simplified cabling and connectors¶ SATA replaces the 40-pin/80-wire PATA ribbon cable with a 7-wire cable. The center connector is for the master device, and the end connector opposite the interface connector is for the slave device.
The graphics card swap introduced a particularly significant change.
Reboot and you should be able to use your drives (you can then start to partition and format your drive). Since it's running in a RAID-1 array and I need to use a similar controller, my BadAxe 2 mainboard will be shipped out to them. Changing the mode after installing the operating system can prevent the system from booting. How Many Hard Drives Can Be Connected To A Single Ide Cable So you can fix the stuff you own quickly—and get back on with your life.
jimmysmittyJul 30, 2010, 2:20 PM aford10 said: There are still RAID drivers for vista and windows 7. Your mobo sounds similiar to mine. When the server posts and the Intel array firmware comes up it did not show the first mirrored array at all. weblink Just make sure your board will support both.
by R. It worked correctly and continues to work correctly.The Intel storage matrix software in windows indicates that the volume was rebuilding by flashing a tray icon. Would have liked LightScribe, but it's not a deal-breaker.2nd EDIT: Just found out (bonk) that those 7200A's are the IDE version. Sole/Only¶ When functioning as master, a few older ATA/ATAPI devices need to know whether they are the only device on the channel, or if a slave device is also connected.
Once that prep work was done, I fired up the Windows 8 setup in earnest. Replace any PIO-only devices if possible. In 2012, voters passed a law that ensured residents' right to repair their car wherever they wanted. I just switched the cables, put my dvd and cd writer drives on the primary IDE cable instead, restarted, and voila!My drive lettering is messed up nowA:floppy C:SATA HD ------ ok
Windows can read from the DVD and HDs just fine, including during setup. Also, there are external drive enclosures available that allow you to install PATA drives in external eSATA cases; for example, the HighPoint RocketMate 1100. Unlike PATA, you needn't set jumpers for master or slave (although SATA does support master/slave emulation). The best rule is simply never to use a 40-wire cable to connect a hard drive.
I first tried 64-bit Windows 8, but was informed that only a clean, fresh install would be performed. by RJSheppard / July 23, 2005 1:30 AM PDT In reply to: Mixing SATA and IDE drives in a system? In IDE mode, the hard drive is set to run as an IDE or Parallel ATA (PATA) hard drive. I cloned the good disk to another disk using disk cloning software on another PC. (i used ghost 4 linux).
The Abit IC7-G is a motherboard built by a defunct company, and it was already running the last available BIOS update. A standard ATA cable may be used with any ATA/ATAPI device through UltraATA-33 (UDMA Mode 2). I haven't really looked at the 22x DVD writers from Samsung and Optiarc so I really can't comment on them yet. "Blu-ray is just a bag of hurt." - Steve Jobs